保定冷干機,冷干機是對壓縮空氣進行后處理，因此選型規則根據空氣壓縮機提供的技術參數來選。主要的參數有以下幾點:
Baoding cold drying machine, the cold dry machine is the compressed air after treatment, so the selection rules according to the technical parameters provided by the air compressor to choose. The main parameters are the following:
1.空氣壓力：冷干機主要處理空氣凈化部分于蒸發器中實現，蒸發器為三類壓力容器。按工作壓力分有低壓型（0.3-0.6MPa）、普通型（0.6-0.95MPa）和中、高壓型（≥1.0MPa）三類，且市場空壓機壓力從低到高種類非常繁多，冷干機壓力選型和儲氣罐一樣，按照空氣壓縮機產生的空氣壓力進行選擇冷干機的壓力類型。一般我公司正常生產都為1.0Mpa下機型，如果高于1.0Mpa上機型需特別定制。
1. air pressure: the cooling dry machine mainly deals with the air purification part in the evaporator, and the evaporator is the three type pressure vessel. According to the working pressure is low (0.3-0.6MPa), ordinary type (0.6-0.95MPa) and high pressure (more than 1.0MPa) three, and the market pressure of air compressor from low to high are very diverse species, cold and dry machine pressure type and gas tank, selection pressure type cold dry air pressure produced by machine air compressor. In general, the normal production of our company for the 1.0Mpa model, if higher than the 1.0Mpa model needs to be specially customized.
2.空氣處理流量：壓縮空氣流量不可超過額定處理量的10%。一般選型時冷干機稍可選則大于空壓機排氣量，這樣空氣處理效果更加。我公司接受 0.5~500 M3/min 及更大氣流量機型的定制。
2. air treatment flow: the compressed air flow can not exceed 10% of the rated capacity. In general, the cold dry machine is slightly larger than the air compressor, so that the effect of air treatment is more. Our company accepts the custom of 0.5~500 M3/min and the more air flow model.
3.壓縮空氣出口溫度：冷干機按進氣溫度高低分有高溫進氣型（80℃以下）和常溫進氣型（45℃以下）；如果高溫的氣體進入常溫機型中，會產生高負載跳閘現象，影響機器的正常運轉。
3., the compressed air outlet temperature: the cold dryer is divided into a high temperature inlet type (below 80 degrees C) and a normal temperature inlet type (below 45 degrees) according to the inlet air temperature. If the high temperature gas enters the normal temperature type, it will cause high load trip phenomenon and affect the normal operation of the machine.
4.冷卻方式：根據制冷系統，可分為水冷型和分冷型兩類。
4. cooling mode: according to the refrigeration system, it can be divided into two types: water cooling type and sub cooling type.
我公司機型的具體選型的型號表示方式如下：
The specific type of model selection of our company model is as follows:
如 TYAD-3F/TYCD-3F 表示處理量為3 m3/min A 表示常溫型,C表示高溫 F 表示風冷型
For example, TYAD-3F/TYCD-3F indicates that the processing quantity is 3 m3/min A to represent the normal temperature type, and C indicates that the high temperature F represents the air cooling type
如TYAD-30W/TYCD-30W 表示處理量為30 m3/min A 表示常溫型,C表示高溫 W 表示水冷型保定冷干機
For example, TYAD-30W/TYCD-30W indicates that the processing quantity is 30 m3/min A to represent the normal temperature type, and C indicates that the high temperature W represents the water-cooled Baoding cold drying machine
冷干機是對壓縮空氣進行后處理，因此選型規則根據空氣壓縮機提供的技術參數來選。主要的參數有以下幾點:
The cold dryer is the post treatment of compressed air, so the selection rules are selected according to the technical parameters provided by the air compressor. The main parameters are the following:
1.空氣壓力：冷干機主要處理空氣凈化部分于蒸發器中實現，蒸發器為三類壓力容器。按工作壓力分有低壓型（0.3-0.6MPa）、普通型（0.6-0.95MPa）和中、高壓型（≥1.0MPa）三類，且市場空壓機壓力從低到高種類非常繁多，冷干機壓力選型和儲氣罐一樣，按照空氣壓縮機產生的空氣壓力進行選擇冷干機的壓力類型。一般我公司正常生產都為1.0Mpa下機型，如果高于1.0Mpa上機型需特別定制。
1. air pressure: the cooling dry machine mainly deals with the air purification part in the evaporator, and the evaporator is the three type pressure vessel. According to the working pressure is low (0.3-0.6MPa), ordinary type (0.6-0.95MPa) and high pressure (more than 1.0MPa) three, and the market pressure of air compressor from low to high are very diverse species, cold and dry machine pressure type and gas tank, selection pressure type cold dry air pressure produced by machine air compressor. In general, the normal production of our company for the 1.0Mpa model, if higher than the 1.0Mpa model needs to be specially customized.
2.空氣處理流量：壓縮空氣流量不可超過額定處理量的10%。一般選型時冷干機稍可選則大于空壓機排氣量，這樣空氣處理效果更加。我公司接受 0.5~500 M3/min 及更大氣流量機型的定制。
2. air treatment flow: the compressed air flow can not exceed 10% of the rated capacity. In general, the cold dry machine is slightly larger than the air compressor, so that the effect of air treatment is more. Our company accepts the custom of 0.5~500 M3/min and the more air flow model.
3.壓縮空氣出口溫度：冷干機按進氣溫度高低分有高溫進氣型（80℃以下）和常溫進氣型（45℃以下）；如果高溫的氣體進入常溫機型中，會產生高負載跳閘現象，影響機器的正常運轉。
3., the compressed air outlet temperature: the cold dryer is divided into a high temperature inlet type (below 80 degrees C) and a normal temperature inlet type (below 45 degrees) according to the inlet air temperature. If the high temperature gas enters the normal temperature type, it will cause high load trip phenomenon and affect the normal operation of the machine.
4.冷卻方式：根據制冷系統，可分為水冷型和分冷型兩類。
4. cooling mode: according to the refrigeration system, it can be divided into two types: water cooling type and sub cooling type.
我公司機型的具體選型的型號表示方式如下：
The specific type of model selection of our company model is as follows:
如 TYAD-3F/TYCD-3F 表示處理量為3 m3/min A 表示常溫型,C表示高溫 F 表示風冷型
For example, TYAD-3F/TYCD-3F indicates that the processing quantity is 3 m3/min A to represent the normal temperature type, and C indicates that the high temperature F represents the air cooling type
如TYAD-30W/TYCD-30W 表示處理量為30 m3/min A 表示常溫型,C表示高溫 W 表示水冷型
For example, TYAD-30W/TYCD-30W indicates that the processing quantity is 30 m3/min A to represent the normal temperature type, and C indicates that the high temperature W represents the water cooling type
